任何物品的长期使用都离不开细心的维护和保养，翅片管也不例外，那么翅片管应该从哪些方面进行具体的保养？让我们看看翅片管专家的介绍。许多客户已经注意到，在使用翅片管的整个过程中，有些翅片管没有得到重视，导致使用寿命短。他们明确提出了维护如何使翅片管的使用寿命更长的问题。一般在操作开始使用清水进行循环时，可能有轻微的漏泄，到温度升到杀菌温度时，漏泄将自行消失。如果漏泄仍不停止，须将翅片管再压紧一些。如果仍不见效，尚须打开检查橡胶垫圈的情况，也有可能是翅片管没有按片上号码顺序排列，则应予纠正。那么翅片管使用后应如何进行保养维护呢？

The long-term use of any article can not be separated from careful maintenance and maintenance, finned tube is no exception, so what aspects should be carried out specific maintenance of finned tube? Let's take a look at the introduction of finned tube experts. Generally, there may be slight leakage when water is used for circulation at the beginning of operation. When the temperature rises to the sterilization temperature, the leakage will disappear automatically. If the leakage does not stop, the finned tube must be pressed down again. If it still fails to work, it is necessary to open and check the rubber gasket. It may also be that the finned tubes are not arranged in the order of numbers on the fins, which should be corrected. How to maintain the fins after use?

1.定期检查各翅片管是否完善，有无沉积物、结焦、水锈层等结垢附着，并及时进行清洗。同时还必须检查各翅片管与橡胶垫圈的粘合是否紧密，橡胶垫圈本身是否完好，以免橡胶垫圈脱胶与损坏而引起的漏泄。

1. Regularly check whether the finned tubes are perfect and whether there are deposits, coking, rust layer and other scales attached, and clean them in time. At the same time, it is necessary to check whether the fin tube and rubber gasket are closely bonded and whether the rubber gasket itself is in good condition, so as to avoid leakage caused by rubber gasket degumming and damage.

2.板式热交换器压紧螺帽与上下导杆，应经常加润滑油脂进行润滑。

2. The compression nuts and upper and lower guide rods of plate heat exchanger should be lubricated with lubricating grease.

3.各仪表调节应有专人负责，并严格执行操作规程进行操作与维护。

3. Special personnel shall be responsible for the adjustment of each instrument, and the operation and maintenance shall be carried out in strict accordance with the operation procedures.

4.当需要更换的橡胶垫圈或修补脱胶部分时，需将该翅片管取下，放在桌上，将旧垫圈拆下，或在脱胶处将翅片管凹槽的胶水遗迹用细砂纸擦净，再用四氯化碳或三氯乙烯等溶剂把凹槽内的油迹擦净，再把新橡胶的垫圈的背部用细砂纸擦磨，同样用四氯化碳或三氯乙烯溶剂把油迹擦净。然后在凹槽和橡胶垫圈背面均薄薄敷上一层胶水，待稍干一下，以不粘手指，但仍发粘为度，将橡胶垫圈嵌入槽内，四周压平，敷一层滑石粉，随即将翅片管装上设备机架轻轻夹紧。根据胶水说明书要求隔一段时间即可投产使用。

4. When the rubber gasket needs to be replaced or the degummed part needs to be repaired, the finned tube should be removed, put on the table, the old gasket should be removed, or the glue residue in the groove should be wiped with fine sandpaper at the degumming place, and the oil stains in the groove should be wiped with carbon tetrachloride or trichloroethylene, and the back of the new rubber gasket should be rubbed with fine sandpaper, and the same with carbon tetrachloride or trichloroethylene The vinyl solvent cleaned up the oil. Then apply a thin layer of glue on the groove and the back of the rubber washer. After a little drying, the rubber washer will not stick to the fingers, but still sticky. Insert the rubber washer into the groove, press the surrounding flat, apply a layer of talcum powder, and then install the finned tube on the equipment rack and clamp it gently. According to the requirements of the glue manual, it can be put into use at intervals.

5.每次将翅片管重新压紧时，须注意上一次压紧时的刻度位置，切勿使橡胶垫圈压过度，以致降低垫圈使用寿命。

5. Each time the finned tube is pressed again, pay attention to the scale position of the last pressing, and do not over press the rubber gasket, so as to reduce the service life of the gasket.

6.更换翅片管橡胶垫圈时，须将该段全部更新，以免各片间隙不均，影响传热效果。

6. When replacing the rubber gasket of finned tube, it is necessary to update the whole section to avoid the uneven gap of each fin and affecting the heat transfer effect.

今天我给大家整理以下常见问题：

翅片管是根据高频焊机技术性再加上斑状板翅式，因此安裝应用中切忌撞击挤压成型，那样会容易形变，更甚至危害排热实际效果。

由于翅片管螺旋式遍布，长期性应用中会出现一些沉淀及水锈层等，我们要立即清理清扫。

翅片管托词处查验连接处是不是松脱和坐垫掉下来。

翅片管曝露在外面的地区防止降水消沉，尽可能维持干躁，间距路面不适合太近，防止蔬菜大棚内浇灌浸蚀了翅片管。

根据对翅片管的维护保养，翅片管的使用年限上面有大的提高。一件物件的长期应用都离不了认真的维护保养和维护，翅片管都不除外，那麼实际要从哪几个方面来对翅片管维护保养维护呢？